Farish wagon runs away - does not couple

[AndyGif]

They are toys.

Blasphemy, you shall hence forth be banished to the land of delprado

[Newportnobby]

They are toys.

Blasphemy, you shall hence forth be banished to the land of delprado

...........there to stand for eternity in silence

[Dr Al]

Coupling to a single wagon with a sprung rapido coupler will always be a problem - this is nothing new. The non sprung Peco Elsie version of the rapido is better in this respect, but still not always reliable.

One thing you could try is reducing the length of the coupler spring to the absolute minimum required to keep is sitting straight - this will reduce the resistance to the coupler raising. Probably not a cure but may help quite a bit. Good thing there is that if you have problems you can replace the spring and return the wagon to original condition.

The other option is to convert to some form of delayed action coupling system, but this is a fair bit of work. I've always preferred to keep rapidos for ease of compatability and selling on of stock if I decide to do so.

Cheers,
Alan

[JeffPreston]

I think the thing that puzzles me the most is that I simply imagined that one might expect that they would couple and that if they don't, they are surely fundamentally at fault.

It seems to me that there are many sides to this and that one can as it were have A and B and C perhaps, but one has to give up on D and E in that case.

If the wagons were heavier that would have to help - but then the loco will struggle with a long rake. 

If the couplers had an even lighter touch - they would be more fragile and cost more.  :'(

I suppose I was coming from the viewpoint of my old childhood days of Triang-Hornby when you could shove those little wagons together with a little nudge and they would couple every time (erm... I think)! Yes - then we have the downside of how to uncouple the little wretches... and the look of the couplers... 

[martink]

Even in larger scales, and even using Kaydees, coupling is still not 100% reliable, and unwanted uncoupling is always a hazard.  Especially with 4-wheel wagons, on curves, at gradient transitions, or tank locos with pony trucks.

[JeffPreston]

I was wondering - is it common practice to have a variety of different types of couplers on a layout? I can imagine that there may for example be rakes of coaches that don't need to get separated that often and this may indeed be prototypical (sorry - I don't know).

Also one can see the fun in shunting    - I look forward to it - but even then I supposed some trucks could perhaps more or less stay together?

In this way one might go for super-fine precision (£££) couplers on just those wagons / coaches that matter?

Next - is there a site or page that shows how to swap out Rapido couplers for something else? Is it easy to do?

Finally - now I'm obsessed     - is there a site or page that shows how to get the roof off this Farish ventilated van (or similar)? Is it easy to do?

[CarriageShed]

Finally - now I'm obsessed     - is there a site or page that shows how to get the roof off this Farish ventilated van (or similar)? Is it easy to do?

It should simply pull off. It's designed to slot into the body, but on older models there are certainly no clips or screws to prevent it coming off easily.

[johnlambert]

I was wondering - is it common practice to have a variety of different types of couplers on a layout? I can imagine that there may for example be rakes of coaches that don't need to get separated that often and this may indeed be prototypical (sorry - I don't know).

Hi Jeff,
I run three types of coupling; Rapido, Dapol dummy knuckle and Dapol magnetic "easy shunt".  I also try to use stock with NEM pockets (either from the manufacturer or converted myself) as this permits easy changing of couplings.

Where practical the Dapol dummy knuckles go between coaches and DMU vehicles as they give closer coupling and are less prone to self-uncoupling.  They are ideal for "semi-fixed" rakes where I'm not planning on changing the coaches in a rake in a running session.

I'm slowly working through my stock adding easy shunt couplings to all of my locos, to the outer ends of brake coaches and to certain wagons which will be formed into sets.  Brake vans get easy shunt couplings at both ends so they can be attached to either end of a train.  I love the ability to do hands free uncoupling with the easy shunt couplings and I'm glad I've adopted them.

Everything else is Rapido.

Having a mix of couplings does mean that you can't run every combination of loco and stock but I've tried to ensure that stuff that would run together can do so.

Next - is there a site or page that shows how to swap out Rapido couplers for something else? Is it easy to do?

I have a feeling there is a section on here for coupling issues where people have shown their work at converting to different couplings.  Hopefully someone will be kind enough to provide a link.

Converting couplings depends on what you want to do and what stock you have.  Anything modern with NEM pockets it is just a matter of pulling out the old coupling and pushing in a replacement.  Dapol does NEM pocket conversion packs, which reqire some cutting and glueing (and a bit of bravery) to replace older style sprung couplings with a socket to take your choice of coupler.  I'm not the most skilled modeller in the world and I managed it but I'd suggest practicing on an un-loved wagon or buying a Peco wagon kit to hack about before taking a knife to your most prized stock.

[JeffPreston]

Whoa - thanks John - lots of information there and a frank discussion of the subject. I think I can see myself heading in a similar direction. Cheers! 

[JeffPreston]

Finally - now I'm obsessed     - is there a site or page that shows how to get the roof off this Farish ventilated van (or similar)? Is it easy to do?

It should simply pull off. It's designed to slot into the body, but on older models there are certainly no clips or screws to prevent it coming off easily.

Thanks Pete - I'll have another look at the rascal! 

[PinkNosedPenguin]

- Thanks for the tip about the sponge on the axles to slow it down - sounds like very precise work! 

I have not done it very precisely at all  . I simply shoved a small piece of foam under the axle and saw how it rolled - then adjusted the foam size so that it ran on its own (so as not to be too much drag on the loco uphill for example) but not as far as without the foam.

IMG_2488 by PinkNosedPenguin, on Flickr
As you can see I am using Dapol easi-shunt couplings and have found these to be a VAST improvement on the standard rapido ones. I can uncouple over a magnet (real hands-free shunting!) and couple up without chasing the wagon halfway round my layout  . The foam helped with the coupling (but also prevented some rather embarrassing unintentional uncouplings when driving forwards over the magnets! They are a bit pricey, but very easy to fit if your rolling stock has NEM pockets (like the photo above) or the Dapol conversion kit allows you to glue pockets onto older stock. I am fitting them to each end (only) of rakes of coaches, but to every wagon so I have complete flexibility when shunting.

I have many wagons that won't couple even if you put a fingertip into each of them and ram them together. Even physically lifting one or the other and trying to thread one coupling onto the other won't work.

Life is just like that. We have to learn to live with it.

Not with these easi-shunt couplings you don't . . .

[JeffPreston]

Whoa PinkNosedPenguin!

Many thanks!

Excellent practical advice and illustrated too - just what I needed. 

This is starting to take shape now - some EZ shunt and others not - sounds like a plan.     I really, really want to be able to play "Shunting Puzzles" without the hand of God needing to be called in. 

[d-a-n]

Easi shunt is the way forward if you want to play hands free shunting. My office layout is made for shunting stuff about on


N gauge hands free shunting

I have some other stuff about Dapol easi shunts on my youtube channel and I have recently done NEM conversion to several items of rolling stock. I was mindful enough to take pictures so I can break it down and show people it happening in action! I'll probably add it onto one of my existing NEM threads but link it up here if this thread's still going in a few days.

EDIT: here you go. Fitting NEM pockets (or 'How I successfully went through the change...')

http://www.ngaugeforum.co.uk/SMFN/index.php?topic=19829.msg202805#msg202805

[JeffPreston]

Thanks Dan! 

Looks like it works for certain. Any problems with unwanted uncoupling? 

[d-a-n]

Looks like it works for certain. Any problems with unwanted uncoupling? 

None with my 4 wheel wagons or bogie stock, even running at low speed over the Kato magnetic track at slow, slow speeds.
I've had some random uncoupling with a really light, free running BG which is coupled to the end of a fast moving parcels train via easi shunts. This uncouples over a hump in the track I've put in deliberately (and badly) so I would say it is most certainly the fault of the builder and operator, not the coupler (or even the track; Kato stuff is lovely.)