!!

Not Registered?

Welcome!  Please register to view all of the new posts and forum boards - some of which are hidden to guests.  After registering and gaining 10 posts you will be able to sell and buy items on our N'porium.

If you have any problems registering, then please check your spam filter before emailing us.  Hotmail users seem to find their emails in the Junk folder.


Thanks for reading,
The NGF Staff.

Author Topic: My 3D printed semaphore signal working like a good'un  (Read 1806 times)

0 Members and 1 Guest are viewing this topic.

Offline Delboy

  • Trade Count: (+1)
  • Full Member
  • ***
  • Posts: 819
  • Country: gb
  • Gender: Male
    • Awards
Re: My 3D printed semaphore signal working like a good'un
« Reply #30 on: October 11, 2019, 11:49:26 AM »

[/quote]

Looking good.

One observation on the EBay listing, in the first video you show your control box, you may be well advised to state that your control box is not included.

Good luck, I'm pretty sure it'll sell well.
[/quote]

Thanks for that @emjaybee.
Do no harm to clarify that point although advert does state that the main photo shows what you are bidding for.
Regards,
She who must be obeyed says I am spending too much time on this forum. I love her dearly but what does she know?

Offline emjaybee

  • Trade Count: (+1)
  • Full Member
  • ***
  • N Gauge Society Number: Yes
  • 2mm Association Number: No
  • Posts: 1935
  • Country: england
  • Gender: Male
  • Grumpy, and proud.
    • Awards
Re: My 3D printed semaphore signal working like a good'un
« Reply #31 on: October 11, 2019, 11:52:12 AM »
Doesn't hurt to clarify, may save some agro.
Sometimes you bite the dog...

...sometimes the dog bites you!

----------------------------------------------------------

I can explain it to you...

...but I can't understand it for you.

Offline REGP

  • Trade Count: (+11)
  • Full Member
  • ***
  • N Gauge Society Number: 19246
  • Posts: 1208
  • Country: england
  • Gender: Male
    • Awards
Re: My 3D printed semaphore signal working like a good'un
« Reply #32 on: October 11, 2019, 03:06:29 PM »


How have I managed to miss this thread up to now?

Congrats @Delboy  youíve made a fantastic little signal and I would love a couple of them (to start with).

If your ebay item was GWR Signal I would be making an offer or two (or more).

I see you actually made half a dozen for another Forum member, are you still prepared to do so, if so Iíll PM you.

Ray

Offline Delboy

  • Trade Count: (+1)
  • Full Member
  • ***
  • Posts: 819
  • Country: gb
  • Gender: Male
    • Awards
Re: My 3D printed semaphore signal working like a good'un
« Reply #33 on: October 11, 2019, 04:10:56 PM »
Hi Ray,
No problems. Glad you like them.
She who must be obeyed says I am spending too much time on this forum. I love her dearly but what does she know?

Offline njee20

  • Trade Count: (+4)
  • Full Member
  • ***
  • N Gauge Society Number: 22598
  • Posts: 5718
  • Country: gb
    • Awards
Re: My 3D printed semaphore signal working like a good'un
« Reply #34 on: October 11, 2019, 04:19:00 PM »
Not my thing at all, but as someone dabbling in 3D printing I applaud you for your stellar results thus far!

 

Please Support Us!
November Goal: £60.00
Due Date: Nov 30
Total Receipts: £35.00
Below Goal: £25.00
Site Currency: GBP
58% 
November Donations


Advertise Here
anything