!!

Not Registered?

Welcome!  Please register to view all of the new posts and forum boards - some of which are hidden to guests.  After registering and gaining 10 posts you will be able to sell and buy items on our N'porium.

If you have any problems registering, then please check your spam filter before emailing us.  Hotmail users seem to find their emails in the Junk folder.


Thanks for reading,
The NGF Staff.

Author Topic: A quick question on wiring leds  (Read 454 times)

0 Members and 1 Guest are viewing this topic.

Online Bealman

  • Moderator
  • Trade Count: (0)
  • Full Member
  • ****
  • N Gauge Society Number: 23151
  • Posts: 14734
  • Country: au
  • Gender: Male
  • Whoops back we go
    • Awards
Re: A quick question on wiring leds
« Reply #15 on: January 02, 2019, 11:48:58 PM »
I've discovered I have two different shades of green, just tested them all with the same 12vdc supply and there is quite a marked difference when lit, and very little difference when unlit.

Did they all come with the position indicator kit/unit or did you buy them separately?    LEDs aren't expensive, I'd be tempted to put that lot to one side for some other use, and just order yourself a new batch.

Yes, I agree. That way you're guaranteed they'll all be the same. Saves all the hassle of trying to get the resistances right to make them all the same brightness.

I note in the Jaycar catalogue that many different light outputs are offered!
Vision over visibility. Bono, U2.

Offline Railwaygun

  • Moderator
  • Trade Count: (+2)
  • Full Member
  • ****
  • N Gauge Society Number: 21889
  • Posts: 4268
  • Country: gb
  • Gender: Male
  • Keen on Military Rail, Kato Unitrack, & Z21/DCC
    • Railwaygun, Armoured train and Military Railway group
    • Awards
Re: A quick question on wiring leds
« Reply #16 on: January 03, 2019, 08:08:59 PM »
you can get versions with built in resistors as well
This has been a public service announcement
It may contain alternative facts

Caveat lector

The largest Railwaygun, Armoured Train & Military Rail group in the world!
https://groups.io/g/railwaygun/topics

My Military Rail Pinterest area
https://uk.pinterest.com/NDRobotnik/

Motto: Semper ubi, sub ubi

Offline sprogman

  • Trade Count: (0)
  • Full Member
  • ***
  • N Gauge Society Number: 17786
  • 2mm Association Number: 4557
  • Posts: 362
  • Country: gb
    • Awards
Re: A quick question on wiring leds
« Reply #17 on: January 04, 2019, 01:29:36 PM »
you can get versions with built in resistors as well

You can, and if they are too bright?...just add a resistor :)

Offline geoffc

  • Trade Count: (0)
  • Full Member
  • ***
  • N Gauge Society Number: 24557
  • Posts: 271
  • Country: gb
  • Gender: Male
    • Awards
Re: A quick question on wiring leds
« Reply #18 on: January 05, 2019, 09:55:52 AM »
If you are buying new LED's why not try one with a variable resistor in the circuit set at 1000 ohms. If it is still too bright adjust the variable resistor until the brightness suits you. Then measure the resistance of the variable resistor and buy the resistors that are closest to this reading.

Geoff

 

Please Support Us!
January Goal: £300.00
Due Date: Jan 31
Total Receipts: £315.00
Above Goal: £15.00
Site Currency: GBP
105% 
January Donations


Advertise Here
anything