Friends,
It is not I that is cracked!
Earlier this year I purchased a new Graham Farish 40145 diesel locomotive for the bargain price of £37.00.
All well and good and today I have eventually got one track usable so thought about running-in whilst I busied myself with other things!
Said locomotive was quite happy circumnavigating the track for about 15 minutes so I reversed the direction. It went about 5 feet and stopped, whirred and refused to continue. I picked it up and studied the bogies, nothing immediately sprang into view!
Replaced on track and it was quite happy again for a couple of circuits and then stopped, again!
Removed from track and was studying the underside when I heard a very audible crack sound?
Gently feeling the play in the gear sets in the bogies I heard the noise again and discovered that part of the underframe moved independently and jammed the drive.
I attempted to use polystyrene glue from the bottle but my hands were shaking so much I feared getting glue on the gear train. So I suspended an opened paper clip in my "Helping Hands" dipped the glue on to the end and raised the locomotive with both hands until the tiniest blob of glue attached itself to the underframe.
After drying all is well again but I suspect that the previous owner had the problem and decided to hand it on to someone else, ME!
Regards, Peter.
Hence the bargain price!
You did better than me I once bought a minitrix 2-6-2 tank engine for a snip on ebay only to recieve a 1-3-1. No drop of glue was going to repair it.
Glad your class 40 is now a goer.
Jerry
Quote from: Jerry Howlett on December 09, 2013, 02:51:37 PM
Hence the bargain price!
You did better than me I once bought a minitrix 2-6-2 tank engine for a snip on ebay only to recieve a 1-3-1. No drop of glue was going to repair it.
Glad your class 40 is now a goer.
Jerry
mono rail to north haverbrook.....
:laughabovepost:
Glad you managed to get it repaired !
Quote from: petercharlesfagg on December 09, 2013, 01:56:44 PM
Earlier this year I purchased a new Graham Farish 40145 diesel locomotive for the bargain price of £37.00
Quote from: petercharlesfagg on December 09, 2013, 01:56:44 PM
After drying all is well again but I suspect that the previous owner had the problem and decided to hand it on to someone else, ME!
??? If it is 'new' (which I doubt it was at that price) there shouldn't be a 'previous owner' to have had any problems...
IF it was sold described as 'New', firstly that suspiciously low price should ave been ringing the alarm bell marked 'avoid'; but at any price, I wouldn't have been fixing a serious fault like a broken component and would have returneded it to the seller requiring a refund or replacement...
Quote from: PLD on December 10, 2013, 06:02:36 PM
Quote from: petercharlesfagg on December 09, 2013, 01:56:44 PM
Earlier this year I purchased a new Graham Farish 40145 diesel locomotive for the bargain price of £37.00
Quote from: petercharlesfagg on December 09, 2013, 01:56:44 PM
After drying all is well again but I suspect that the previous owner had the problem and decided to hand it on to someone else, ME!
??? If it is 'new' (which I doubt it was at that price) there shouldn't be a 'previous owner' to have had any problems...
IF it was sold described as 'New', firstly that suspiciously low price should ave been ringing the alarm bell marked 'avoid'; but at any price, I wouldn't have been fixing a serious fault like a broken component and would have returneded it to the seller requiring a refund or replacement...
I am sure that you are aware of the saying "There's no fool like an old fool!" I am he!
I always fall for the sob story and the "bargain"!
I would return it to the seller If I knew who or where he, she or it was but they have "ceased trading"!
On the other hand I am always willing to admit my mistakes and try and patch up the problem rather than climb on to my soap box!
I appreciate what you have written, I also hope that others do not follow me down this path!
..............................................................................................."...................................................................................
As it is the repair failed again and I will have to consider a professional repairer since I am inadequate to the task! Warmest regards, Peter.
I find that glueing a lot of the plastics used isn't really that likely to work. Acetal in particular is a b*gger to glue to anything.
For the 40 you should be able to get the needed plastic bits as spares easily enough. For repair it depends where the damage is but if it bears any load then usually means dismantling until the plastic part you need to repair is liberated and then either judicious rather naughty abuse of a soldering iron or drilling two small holes and screwing the bits together with a bit of metal or additional plastic as a reinforcement.
Alan
Quote from: EtchedPixels on December 13, 2013, 12:08:21 AM
I find that glueing a lot of the plastics used isn't really that likely to work. Acetal in particular is a b*gger to glue to anything.
For the 40 you should be able to get the needed plastic bits as spares easily enough. For repair it depends where the damage is but if it bears any load then usually means dismantling until the plastic part you need to repair is liberated and then either judicious rather naughty abuse of a soldering iron or drilling two small holes and screwing the bits together with a bit of metal or additional plastic as a reinforcement.
Alan
Thank you Alan,
Things are a little more serious than I had anticipated and I have contacted Bob and will be sending the locomotive to him in January!
I suspect several problems with the bogie are causing more headaches. The rearmost drive axle on one of the bogies seizes up and the bogie itself is SO stiff in the mounting that it will not twist for corners, thereby answering the question of why it left the tracks!
thankyou for your interest, I really appreciate it, regards, Peter.
Hello Peter,
I'm also an old sucker that falls for 'bargains' sometimes it pays off but sometimes I get real lemons.
I have learned quite a lot about taking locos apart and putting them together though. :D
:NGaugersRule:
This stuff was mentioned on a thread about gluing Delrin from a couple of years ago on RMWEB
http://www.reltekllc.com/bondit-b45th.html (http://www.reltekllc.com/bondit-b45th.html)