!!

Not Registered?

Welcome!  Please register to view all of the new posts and forum boards - some of which are hidden to guests.  After registering and gaining 10 posts you will be able to sell and buy items on our N'porium.

If you have any problems registering, then please check your spam filter before emailing us.  Hotmail users seem to find their emails in the Junk folder.


Thanks for reading,
The NGF Staff.

Author Topic: Precision Labels - Pullman conversions (for original 1980s Farish Pullmans)  (Read 717 times)

0 Members and 1 Guest are viewing this topic.

Offline Dsolds

  • Trade Count: (0)
  • Full Member
  • ***
  • Posts: 89
  • Country: gb
  • Gender: Male
    • Awards
This is fascinating to me, thanks so much for sharing. Regarding the transfers, can I ask which ones you used? I only see water slide transfers when I search for them but you mention plastic printed labels.

Also, you mention internal mods, what do you have in mind? I was thinking about trying to make the table lamps light up with micro LEDs rather than having roof lighting. The Hornby OO Pullman’s have this and I believe the N gauge Brighton Belle carriages do as well.

Offline Snowwolflair

  • Trade Count: (+1)
  • Full Member
  • ***
  • N Gauge Society Number: 25174
  • 2mm Association Number: 4194
  • Posts: 1647
  • Country: gb
  • Gender: Male
    • Awards
http://www.precisionlabels.com/l12.html?

this is the correct set of plastic labels.  They are like vinyls but have a greater rigidity.

Offline Snowwolflair

  • Trade Count: (+1)
  • Full Member
  • ***
  • N Gauge Society Number: 25174
  • 2mm Association Number: 4194
  • Posts: 1647
  • Country: gb
  • Gender: Male
    • Awards
A quick aside.

whilst rummaging around for the King Arthur I remembered I had the Arch Laser kit to convert a G siphon into Winston Churchill's funeral coach. As it can be used with Pullmans and carried the same livery (as now restored) I decided to start putting it together.  It's a bit fiddly but worth the extra work.

Stage 1 tonight to get the body cut up and reassembled.  Before anyone says you have put the floor in without internal painting and glazing, the kit floor is really a jig to set the coach width and I will cut most of it out later  :)




Offline Snowwolflair

  • Trade Count: (+1)
  • Full Member
  • ***
  • N Gauge Society Number: 25174
  • 2mm Association Number: 4194
  • Posts: 1647
  • Country: gb
  • Gender: Male
    • Awards
First coats of paint and it looks quite good, although the wood grain is hard to smooth.



Offline Shiney Sheff

  • Trade Count: (+1)
  • Full Member
  • ***
  • N Gauge Society Number: 23792
  • Posts: 257
  • Country: 00
    • Awards
First coats of paint and it looks quite good, although the wood grain is hard to smooth.





Are you using acrylic paint? if so, because it is water based it will always bring the grain up, ideally you need oil based paints to stop this happening.

Offline Snowwolflair

  • Trade Count: (+1)
  • Full Member
  • ***
  • N Gauge Society Number: 25174
  • 2mm Association Number: 4194
  • Posts: 1647
  • Country: gb
  • Gender: Male
    • Awards
The wood was sealed prior to painting, however it is a very open grain ply and to fill out the grain completely would wipe out the detail.

Offline Snowwolflair

  • Trade Count: (+1)
  • Full Member
  • ***
  • N Gauge Society Number: 25174
  • 2mm Association Number: 4194
  • Posts: 1647
  • Country: gb
  • Gender: Male
    • Awards
This photo illustrates the problem with laser multi depth cutting.  Where the laser does not burn the wood is smooth and where the surface is burned to form panel detail it is rough, and its not a wood grain problem.  Unfortunately there is no way to sand these areas efficiently, and over painting only has limited benefit.  This is particularly a problem at the paint edge as a brush picks up the rough surface, however this can be partially solved with an indelible brown felt pen to draw the edge with a steel rule.  The model will get a lite rub with a fiberglass pen and a coat of gloss varnish which will also improve the situation.


« Last Edit: Yesterday at 12:51:58 pm by Snowwolflair »

Offline Snowwolflair

  • Trade Count: (+1)
  • Full Member
  • ***
  • N Gauge Society Number: 25174
  • 2mm Association Number: 4194
  • Posts: 1647
  • Country: gb
  • Gender: Male
    • Awards
Significant progress tonight.  :beers:

The brakes Car No.94 and Car No.95 are 12 wheeler coaches. and with a little work Atlas/Rivarossi Pullman bogies are perfect.  8)

The under body will need modified to suit but that's simple.

12 wheel


8 wheel

« Last Edit: Yesterday at 10:32:59 pm by Snowwolflair »

 

Please Support Us!
January Goal: £55.00
Due Date: Jan 31
Total Receipts: £55.00
Below Goal: £0.00
Site Currency: GBP
100% 
January Donations


Advertise Here