!!

Not Registered?

Welcome!  Please register to view all of the new posts and forum boards - some of which are hidden to guests.  After registering and gaining 10 posts you will be able to sell and buy items on our N'porium.

If you have any problems registering, then please check your spam filter before emailing us.  Hotmail users seem to find their emails in the Junk folder.


Thanks for reading,
The NGF Staff.

Author Topic: Beyer Garret kit build, advice and photos needed  (Read 811 times)

0 Members and 1 Guest are viewing this topic.

Offline Dr Al

  • Trade Count: (+49)
  • Full Member
  • ***
  • Posts: 4160
  • Country: gb
  • Gender: Male
    • Awards
Re: Beyer Garret kit build, advice and photos needed
« Reply #15 on: February 02, 2018, 03:20:30 pm »
OUCH Alan, I have a new skill then to master, whilst I can Mig weld, stick weld, braze, electrical solder, this will be a new skill to investigate and learn. Who sells the low melt solder? Do I use Bakers flux?
Kind regards from Fred

You need correct flux suitable for whitemetal.

I use Carr's Red label flux, available from Phoenix precision and also 70degree solder from them. You also will need a temperature controlled iron, set below the melting point of whitemetal, otherwise you'll likely end up with more holes or a big blob!

Cheers,
Alan
Quote from: Roy L S
If Dr Al is online he may be able to provide a more comprehensive answer.

Online Fredastaire

  • Trade Count: (0)
  • Full Member
  • ***
  • Posts: 162
  • Country: gb
    • Awards
Re: Beyer Garret kit build, advice and photos needed
« Reply #16 on: June 06, 2018, 11:45:59 am »
After a while in limbo on another huge home project ive now picked up The Beyer Garret to finish it this time. Ive built two very good speed compatable Black 5 chassis so her we go, (one to be reversed yet as I build the water tender section).
The Lytchett castings as ive mentioned before are quite terrible however as theve now stopped making them i'm going to fill and file as needed as once its in paint nobody will ever know.
Now the reason for this note.
1/,i'm struggling with trying to fit the firebox bottom, its not clear how it should fit and which way up, there is a flat panel, is this to the bottom or the top? does this firebox casting totally secure the pivoting tender chassis? if I fit as cast it will lock the tender chassis straight. the cast inclined angles of the hinge down ashpan also appear back to front.
2/, is the finished model supposed to be 'one piece' for transport / storage or are the two pivotting sections detatchable from the main loco boiler / cab?
Kind regards from Fred


Offline Dr Al

  • Trade Count: (+49)
  • Full Member
  • ***
  • Posts: 4160
  • Country: gb
  • Gender: Male
    • Awards
Re: Beyer Garret kit build, advice and photos needed
« Reply #17 on: June 06, 2018, 11:50:28 am »
1/,i'm struggling with trying to fit the firebox bottom, its not clear how it should fit and which way up, there is a flat panel, is this to the bottom or the top? does this firebox casting totally secure the pivoting tender chassis? if I fit as cast it will lock the tender chassis straight. the cast inclined angles of the hinge down ashpan also appear back to front.
2/, is the finished model supposed to be 'one piece' for transport / storage or are the two pivotting sections detatchable from the main loco boiler / cab?

1. You have the firebox bottom in the correct general location, but you want to move it forward (i.e. to the right on you picture) to ensure no clashes with the pivoting chassis and also align it with the actual firebox on the boiler. This may need some fettling of the casting and underside to make it fit, as the Lytchett castings were getting worn and poorly shaped in late days.

2. Yes, it's a three piece loco - the two powered chassis and the central boiler spanning them should detach for ease of storage and transport - one on the peg in the cab roof, the other to the long bolt on the front footplate ahead of the smokebox door.

Cheers,
Alan
Quote from: Roy L S
If Dr Al is online he may be able to provide a more comprehensive answer.

Online Snowwolflair

  • Trade Count: (+1)
  • Full Member
  • ***
  • N Gauge Society Number: 25174
  • 2mm Association Number: 4194
  • Posts: 2181
  • Country: gb
  • Gender: Male
    • Awards
Re: Beyer Garret kit build, advice and photos needed
« Reply #18 on: June 06, 2018, 12:01:39 pm »
As Al says these should be in line.




Online Fredastaire

  • Trade Count: (0)
  • Full Member
  • ***
  • Posts: 162
  • Country: gb
    • Awards
Re: Beyer Garret kit build, advice and photos needed
« Reply #19 on: June 09, 2018, 09:32:57 am »
I'm pleased to report progress. thanks gents for the advice on the ash pan / firebox.
The photo is dry assembled major parts not glued.
I'm now planning to prime these major compnents so I can then use 'automotive knifing stopper' (in the old days we called it cellulose stopper), to fill grooved and pock holes so that I can use wet n dry paper to smooth off before further priming before assembly.
Comments and advice appreciated


Online Fredastaire

  • Trade Count: (0)
  • Full Member
  • ***
  • Posts: 162
  • Country: gb
    • Awards
Re: Beyer Garret kit build, advice and photos needed
« Reply #20 on: June 20, 2018, 11:34:53 pm »
Im pleased to say that the Beyer garret has finally made it to our club layout for its first run. After many hours of filing and filling all the blow holes and missing areas ive used Halfords grey undercoat and their black semi gloss, now looks quite good, ive just to solve fixing the transfers as my first attempt didnít work, the transfers wouldnít stick, I guess iím going to spot gloss to give a transfer the chance to stick, any advice welcome as iím new to this. The bogies took some work, the couplings were only part there so i cut the cast bits off and using a jewellers saw cut slots into which I fitted Farish shortened NEM couplers finally fixed with a taper clock pin. The wheels were a cause for thought, none were in the kit, the Black five had too finer axles, solved by using China Farish wagon spoked wheels; carefully removed the wheels, ground the points off. Next problem was how to insulate; back to my scrap box; I have in recent times rebuilt two flying bananas so had the old armature white plastic bearing rectangles, these have a tiny extension Ďtubeí easily sliced off these provided insulating spacers to keep the wheel tyres off the bogie block.
Ive a bit of trouble with the assembled loco not always starting on both motors even tho both chassis are fine as independent units, first iím going to add a tiny washer under the smoke box, the finished loco is so heavy that its got no axial flex and i think it suffers from one chassis wheels being lifted off the track just a fraction and loosing electric contact, if the washer isnít effective iím going to add a wire from water tender to coal tender on the Ďinsulatedí wiring.
Any comments on these or further mods appreciated.



Offline Foster

  • Trade Count: (0)
  • Full Member
  • ***
  • Posts: 19
  • Country: za
    • Awards
Re: Beyer Garret kit build, advice and photos needed
« Reply #21 on: June 21, 2018, 03:44:03 am »
 You have made a fine model.
 I am in Pinetown, South Africa, and spent many hours watching the SAR Garretts at work near Pietermaritzburg in my youth,
 so I am a Garrett nut. :beers:     

Offline Railwaygun

  • Moderator
  • Trade Count: (+2)
  • Full Member
  • ****
  • N Gauge Society Number: 21889
  • Posts: 3851
  • Country: gb
  • Gender: Male
  • Keen on Military Rail, Kato Unitrack, & Z21/DCC
    • Railwaygun, Armoured train and Military Railway group
    • Awards
This has been a public service announcement
It may contain alternative facts

Caveat lector

The largest Railwaygun, Armoured Train & Military Rail group in the world!
https://groups.io/g/railwaygun/topics

My Military Rail Pinterest area
https://uk.pinterest.com/NDRobotnik/

Motto: Semper ubi, sub ubi

Offline Bealman

  • Moderator
  • Trade Count: (0)
  • Full Member
  • ****
  • N Gauge Society Number: 23151
  • Posts: 13251
  • Country: au
  • Gender: Male
  • Whoops back we go
    • Awards
Re: Beyer Garret kit build, advice and photos needed
« Reply #23 on: June 21, 2018, 06:07:42 am »
You have made a fine model.
 I am in Pinetown, South Africa, and spent many hours watching the SAR Garretts at work near Pietermaritzburg in my youth,
 so I am a Garrett nut. :beers:     

Totally agree. An excellent job of a fascinating locomotive.  :thumbsup:
Vision over visibility. Bono, U2.

Online Newportnobby

  • Global Moderator
  • Trade Count: (+59)
  • Full Member
  • *****
  • N Gauge Society Number: 21962
  • Posts: 28386
  • Country: england
  • Gender: Male
    • Awards
Re: Beyer Garret kit build, advice and photos needed
« Reply #24 on: June 21, 2018, 10:06:42 am »
Very nice work, Fred :claphappy:

Online Fredastaire

  • Trade Count: (0)
  • Full Member
  • ***
  • Posts: 162
  • Country: gb
    • Awards
Re: Beyer Garret kit build, advice and photos needed
« Reply #25 on: June 21, 2018, 10:29:45 am »
May i say thanks to all of you who have given advice so far, ive really appreciated the help. As my first Ďwhite metal kití its been a real leaning curve.
 After sorting the transfers and the red buffer beams im on to completing LMS 10000 and starting 10001.
Thanks again, rgds Fred

 

Please Support Us!
June Goal: £55.00
Due Date: Jun 30
Total Receipts: £60.00
Above Goal: £5.00
Site Currency: GBP
109% 
June Donations


Advertise Here